Underwater Laser Scanning

Millimetre accuracy, underwater

Subsea laser scanners sweep a precise line of light across welds, pipe walls and components, capturing millions of points with millimetre accuracy. It is the closest thing to a tape measure you can take below the surface.

mmLevel accuracy
1.4MPoints per weld scan
360°Rotating scan
350 mScanner depth rating
Real scan data
An HDPE pipe fusion weld, measured to the millimetre.
Interactive demo · real data

Inside a Laser-Scanned Weld

This is a real ROV laser scan of a fusion weld inside a 1.05 m HDPE pipeline, reduced from 1.6 million points. Colours show how far the wall sits from a perfect cylinder. The model starts at true scale. Boost the relief to exaggerate the shape, unroll the pipe flat, or move the profile line to see the internal fusion bead and the ovality around the weld.

Pipe boreScanned lengthPeak deviationProfile angle
Deviation from ideal cylinder
-10 mm0+10 mm
Drag to rotate · scroll to zoom

Sample from a deep-water pipeline weld inspection, shown without client or location details. Each weld in the full deliverable was scanned at about 1.4 million points over a 0.5 m length.

Why laser
Every engineer asks the next question: how big?
Why we started

From Two Laser Dots to Millimetre Models

"Every engineer asks the same question after an inspection: how big is it?"Alex & Adrian, AUS-ROV

Our laser scanning started with a client who needed to understand the internal condition of a critical pipeline. We were inspecting it with ROV video and finding defects, and the engineer's next question was always how big is that pitting, that weld erosion, that dent?

Two parallel laser dots set 100 mm apart gave us a scale in every frame, but it was never a true measurement of the anomaly. A 3D laser scanner was the logical next step, delivering millimetre-accurate models of the defect itself. Since then we've laser scanned welds, pipe sections and components on project after project.

How it works
A line of light. A calibrated camera. Millions of points.
How it works

Laser Triangulation

A green or blue laser projects a thin line onto the surface. A calibrated camera, offset at a known angle, sees where the line lands. Because the geometry is fixed, every pixel along the line becomes a measured 3D point.

With the ROV held still, the scanner rotates through a full 360°, and thousands of these profiles build up a dense, true-scale point cloud of the weld, pipe or component.

  • Millimetre accuracy at close range
  • Full 360° sweep from a single position
  • Working range from 0.36 m to 2.5 m
From the field
No second chances during a shutdown.
From the field

A Deep-Water Weld Scan During a Mining Shutdown

A mining operation couldn't restart until it had verified confidence that a critical deep-water pipeline was still serviceable. The scans had to be right, and they had to be done within the shutdown window.

The challenge

Integrate a laser scanner onto the ROV, fly it into the pipeline and down to depth, then hold perfectly still while the scanner rotates through a full 360° around each weld.

Our approach

We designed and built a custom skid that docks with the ROV and holds the scanner exactly on the pipe centreline. Contingencies covered breakdowns, site issues and even power blackouts, so nothing could stop the program.

The result

Clean raw data for every weld, about 1.4 million points each, processed into 3D models and deviation reports and delivered on time, giving the operator the confidence to restart.

Deep-water pipeline360° weld scansCustom ROV skidShutdown critical
Applications
Where millimetres decide the next step.
Applications

Where Laser Scanning Helps

01

Pipeline Welds

Fusion bead size, joint misalignment, ovality and deformation at welded and fused joints inside pipelines and outfalls.

02

Pipe Sections & Components

Internal condition, ovality and deformation of pipe sections, and as-built dimensions of flanges, valves and fittings for repair and fabrication.

03

Mooring Chains

Link diameter and interlink wear measured against nominal size, with results reviewed by an engineer who specialises in worn and corroded mooring chain.

04

Corrosion & Pitting

Depth and extent of pitting and metal loss, assessed against remaining strength by our consultant engineer.

05

Piles & Structures

Section loss and deformation of piles, braces and supports, with structural engineering review where it matters.

06

Change Monitoring

Repeat scans compared point-for-point to show what has moved, worn or grown over time.

Engineering behind the data

Our consultant engineer is a chartered structural engineer and naval architect with 30 years in offshore energy and defence. He has led industry research into the remaining strength, fatigue and corrosion of mooring chain, and has reviewed AUS-ROV inspection findings since 2017. So you get an engineering answer, not just a point cloud.

Honest advice
The right tool, not the most expensive one.
Honest advice

When Laser Isn't the Answer

Laser needs clear water. Many of our dams and water assets don't have it.

Sonar and laser aren't interchangeable; each gives a different kind of result. So the first thing we scope with you is the water itself: turbidity (NTU), total suspended solids (TSS), and whether the structure can be cleaned, the water flushed or the system isolated to give a clear window for scanning.

If laser can't work, we'll tell you, and recommend the sonar or hybrid approach that will give you the best answer within what the technology can deliver.

  • Water quality assessed before mobilisation
  • Cleaning, flushing or isolation options considered
  • Sonar or hybrid recommended where laser won't perform
Results
Clean data. Clear decisions.
Gallery

Laser Scan Results

Laser scan of a pipe interior coloured by intensity

Pipe interior laser scanned from the ROV, coloured by intensity, showing branch openings and joints.

Laser scanned pipe section coloured by deviation

A laser-scanned pipe section coloured by deviation, making wall loss and deformation obvious at a glance.

AUS-ROV technician preparing the ROV laser scanning rig

Preparing the ROV laser scanning rig, with a centring frame that keeps the scanner on the pipe axis.

Laser scan data being reviewed live in the topside control station

Live data review topside, so coverage is confirmed before the ROV leaves the pipe.

Our capability
Short range. Extreme detail.
Equipment

Our Laser Scanning Capability

360° rotating laser scanner
Working range0.36 m to 2.5 m
AccuracyMillimetre level
Scan geometry50° fan with full 360° rotation
Depth rating350 m
Best forStationary scans of welds, pipe sections and components

Processed by AUS-ROV and our network of specialist survey partners. Deliverables as LAS, E57, XYZ, OBJ/PLY meshes and deviation reports.

Let's talk
Need a measurement you can trust?

Need Millimetre Answers Underwater?

Tell us what needs measuring. We'll confirm whether laser, sonar or a combination will deliver the accuracy you need.